www.megadrum.info

by **d4ri0** » Sat May 08, 2010 7:25 am

Hello ! My names Dario. Im from Argentina.
Im a newbie on electronics.
What version of MegaDrum i have to build, to connect the module to the PC via USB ? Because i dont have a Midi In/Out connectors in my PC, only USB.
Sorry if my english its so basic.

Thanks a lot ! Sorry if the section of my post is wrong

by **dmitri** » Sat May 08, 2010 11:32 am

The Digital Board includes USB so any version will do USB.

by **AnjiN** » Mon Jun 21, 2010 2:37 pm

Hello!

I have no knowledge in electronics, so it may be a silly question...

I was looking the input sockets schematics and I got confused about HH pedal jack's wiring.

Should I wire both 2-1 and 2-3, or choose wiring 2-1 or 2-3?

Sorry by bad english!

--

Anjin.

by **dmitri** » Mon Jun 21, 2010 2:59 pm

SW1 is a switch to select High or Low impedance HiHat pedal input to better match impedance of a pedal.

by **gerardomgallo** » Sat Oct 16, 2010 2:54 am

The supply of current, where it connects?

by **dmitri** » Sat Oct 16, 2010 10:41 am

gerardomgallo wrote:The supply of current, where it connects?

USB

by **Rogui** » Sat Feb 12, 2011 9:14 pm

Hi Dmitri,

I’m brazilian and I built a megadrum 32 last week, but I didn’t see that I need new protected bootloader and firmware encrypted to megadrum works. Then, can I find de older bootloader and the last firmware unencrypted in the forum for my megadrum works?

Sorry for my bad English.

Tks.

by **dmitri** » Sat Feb 12, 2011 10:20 pm

It is in the forum FAQ

by **jjpl2001** » Sat Jun 11, 2011 1:08 pm

Hi where can I find the 56 input schematics? thanks

by **timero** » Tue Jun 28, 2011 2:48 pm

hi! im new with diy.. it my 1st time trying since i really want to build this beast. i have no knowledge in schematics that's why im studying through the net for a week now just to gain a few understanding of building the megadrum.. now i think i can start building my own megadrum but i just wanted to ask some things before i begin with this project.

1st. i wanted to use 4851's so i wont have to use the BATs. i read in this thread that i can still use the analogue pcb (just remove the BATs and replace input protection resistors with jumpers)
Q: what resistors should i replace? Are they R2,R6,R10 and R14?

2nd. I really don't know where to use the IC sockets (are they suppose to be connected to the pins of the IC's?), PINS array 36x1 and cable mounting sockets?

sorry for a very newbie questions i just wanted to clarify this things so everything will go smoothly when i actually start building my own megadrum.

please be easy on me..

Thanks..

www.megadrum.info

Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Re: Latest MegaDrum schematics. 32 inputs.

Who is online