Hi there!
You said earlier that you got values between 11-13. Is these figures what you see on the MD's related PS screen? No impact if changing the high/low PS levels?
Anders
Everson MD REbuild
Re: Everson MD REbuild
by angr77 » Thu Feb 21, 2013 5:58 pm
Sonor, Drum-Tec heads, Roland CY14, CY12&15R, 2x BT-1 & VH11, 12, 13, Triggera D11, 2xD14, Pintech Dingbat, Letric Moo, Quartz triggers, 2xARM based MegaDRUM, PS Board, M-Audio FT Ultra 8R, Addictive Drums 2.1.6, Surface Pro 5 http://zourman.com
- angr77
- Posts: 622
- Joined: Tue Nov 29, 2011 10:42 pm
- Location: Stockholm, Sweden
Re: Everson MD REbuild
by everson » Fri Feb 22, 2013 7:13 am
Yup, that`s where I watch them.
Now, it`s only 11, 99% of time ...
Now, it`s only 11, 99% of time ...
- everson
- Posts: 165
- Joined: Mon Jan 02, 2012 10:14 pm
Re: Everson MD REbuild
by angr77 » Sun Feb 24, 2013 9:13 am
What is your minscan set to?
Sonor, Drum-Tec heads, Roland CY14, CY12&15R, 2x BT-1 & VH11, 12, 13, Triggera D11, 2xD14, Pintech Dingbat, Letric Moo, Quartz triggers, 2xARM based MegaDRUM, PS Board, M-Audio FT Ultra 8R, Addictive Drums 2.1.6, Surface Pro 5 http://zourman.com
- angr77
- Posts: 622
- Joined: Tue Nov 29, 2011 10:42 pm
- Location: Stockholm, Sweden
- everson
- Posts: 165
- Joined: Mon Jan 02, 2012 10:14 pm
Re: Everson MD REbuild
by angr77 » Sat Mar 16, 2013 2:48 pm
Coming back to the PS issue...did you use 35 or 27 mm type of triggers?
On my implementation the Head trigger is reversed connected on the piezo. The brass part, e.g black cable is the one which is connected to the tip part of the tele plug. Red is for ground.
The rim trigger is connected as usual. This is the Roland way to do it.
I am currently doing some PS test on my CY-15R...it is supporting PS...but I have problems to make it move smooth enough...could be the min scan....
Angr77
On my implementation the Head trigger is reversed connected on the piezo. The brass part, e.g black cable is the one which is connected to the tip part of the tele plug. Red is for ground.
The rim trigger is connected as usual. This is the Roland way to do it.
I am currently doing some PS test on my CY-15R...it is supporting PS...but I have problems to make it move smooth enough...could be the min scan....
Angr77
Sonor, Drum-Tec heads, Roland CY14, CY12&15R, 2x BT-1 & VH11, 12, 13, Triggera D11, 2xD14, Pintech Dingbat, Letric Moo, Quartz triggers, 2xARM based MegaDRUM, PS Board, M-Audio FT Ultra 8R, Addictive Drums 2.1.6, Surface Pro 5 http://zourman.com
- angr77
- Posts: 622
- Joined: Tue Nov 29, 2011 10:42 pm
- Location: Stockholm, Sweden
Re: Everson MD REbuild
by everson » Sun Mar 17, 2013 6:33 pm
It's a 35mm quartz trigger (their cone, piezo and foamy dst) on my alu crossbar.
Wiring is Alesis type, as far as I remember (I switched from Roland to Alesis a couple of times).
What I just noticed is if I raise the MinScan to ~100, the things start to getting better. But that looks like a very odd/slow minscan setting ...
Wiring is Alesis type, as far as I remember (I switched from Roland to Alesis a couple of times).
What I just noticed is if I raise the MinScan to ~100, the things start to getting better. But that looks like a very odd/slow minscan setting ...
- everson
- Posts: 165
- Joined: Mon Jan 02, 2012 10:14 pm
Re: Everson MD REbuild
by everson » Sun Mar 17, 2013 6:35 pm
BTW, Triggera is now very close to releasing the china 
- everson
- Posts: 165
- Joined: Mon Jan 02, 2012 10:14 pm
Re: Everson MD REbuild
by angr77 » Sun Mar 17, 2013 9:05 pm
Min scan set to 100 sounds extremely high...i am using 50.
Just for curiosity...What made you to pick the Alesis/yamaha way to wire the piezos?..(in my case...I am more of a Roland guy...that's why i picked the Roland way...no science behind picking the solution)
Sounds lovely regarding the Triggera China...i am going to buy one!
Best Regards
Angr77
Just for curiosity...What made you to pick the Alesis/yamaha way to wire the piezos?..(in my case...I am more of a Roland guy...that's why i picked the Roland way...no science behind picking the solution)
Sounds lovely regarding the Triggera China...i am going to buy one!
Best Regards
Angr77
Sonor, Drum-Tec heads, Roland CY14, CY12&15R, 2x BT-1 & VH11, 12, 13, Triggera D11, 2xD14, Pintech Dingbat, Letric Moo, Quartz triggers, 2xARM based MegaDRUM, PS Board, M-Audio FT Ultra 8R, Addictive Drums 2.1.6, Surface Pro 5 http://zourman.com
- angr77
- Posts: 622
- Joined: Tue Nov 29, 2011 10:42 pm
- Location: Stockholm, Sweden
Re: Everson MD REbuild
by dmitri » Sun Mar 17, 2013 9:08 pm
angr77 wrote:Just for curiosity...What made you to pick the Alesis/yamaha way to wire the piezos?..(in my case...I am more of a Roland guy...that's why i picked the Roland way...no science behind picking the solution)
With the Positional sensing addon board I don't think the polarity of the central piezo has any effect.
- dmitri
- Site Admin
- Posts: 8709
- Joined: Fri Aug 03, 2007 8:05 pm
Re: Everson MD REbuild
by angr77 » Sun Mar 17, 2013 9:16 pm
Dmitri! Hope everthing is well!
Good to know regarding the polarity. My PS implementation is working extremly good using AD and set the snare to receive on cc16 and use AD's cc sampled drum sound...great!!
Best Regards
Angr77
Good to know regarding the polarity. My PS implementation is working extremly good using AD and set the snare to receive on cc16 and use AD's cc sampled drum sound...great!!
Best Regards
Angr77
Sonor, Drum-Tec heads, Roland CY14, CY12&15R, 2x BT-1 & VH11, 12, 13, Triggera D11, 2xD14, Pintech Dingbat, Letric Moo, Quartz triggers, 2xARM based MegaDRUM, PS Board, M-Audio FT Ultra 8R, Addictive Drums 2.1.6, Surface Pro 5 http://zourman.com
- angr77
- Posts: 622
- Joined: Tue Nov 29, 2011 10:42 pm
- Location: Stockholm, Sweden
Who is online
Users browsing this forum: No registered users and 13 guests